Fluid Power World

  • Home
  • Technologies
    • Hydraulics
      • Cylinders & Actuators
      • Filtration/Contamination Control
      • Fittings, Couplings & Adapters
      • Fluids
      • Fluid Conditioning
      • Hose & Tubing
      • Pumps & Motors
      • Related Technologies
      • Sealing
      • Sensors & Gauges
      • Valves & Manifolds
    • Pneumatics
      • Air Preparation & Regulation
      • Compressed Air Technologies
      • Cylinders & Actuators
      • End Effectors & Grippers
      • Fittings, Couplings & Adapters
      • Hose & Tubing
      • Sensors
      • Vacuum
      • Valves & Manifolds
  • Engineering Basics
  • Trending
  • Resources
    • Digital Issues
    • Pneumatics Tech Toolbox
    • Podcasts
    • Special Reports
    • Subscribe to Fluid Power World Print Magazine
    • Videos
    • Webinars / Digital Events
    • White Papers
  • Women in Engineering
    • Women in Fluid Power
    • Women in Engineering
  • Design Guides
  • Classrooms
    • Hydraulic Filtration
    • Hydraulic System Design
    • Pneumatics Classroom
  • Advertisers
    • Advertise
    • PR Submissions
    • Eblast Submissions
  • SUBSCRIBE

Compressed air fail: The water problem that started at the cooling air intake

By Paul Heney | September 19, 2026

Share

By Ron Marshall

When Sarah’s phone rang for the third time that week about water in the compressed air system, she assumed she already knew where the problem was. The maintenance supervisor reported water collecting in filter bowls, operators complained that pneumatic cylinders were becoming sluggish, and one production line had experienced quality problems because moisture had reached the equipment.

Everything seemed to point toward the refrigerated dryer. Sarah, the plant’s maintenance manager, arranged for the dryer to be serviced, replaced several filter elements, and asked her team to inspect the automatic condensate drains. The technician confirmed that the dryer was operating as designed. Its refrigeration circuit was healthy, the condensate drain was functioning properly, and the outlet dew point was within the expected range.

Yet the complaints continued, and Sarah knew they were missing something. If the dryer was working properly, she needed to understand why water was still appearing farther downstream. Rather than approving the purchase of a replacement dryer, Sarah decided to investigate the compressor room herself. She had learned over the years that the location of a symptom is not always the location of its cause.

Have a cool unrestricted supply of ventilation air entering your compressor room to keep air cooled compressors running properly. Often ventilation problems show up as water problems, so you must be vigilant
Fig. 1. It is very important to have a cool unrestricted supply of ventilation air entering your compressor room to keep air cooled compressors running properly. Often ventilation problems show up as water problems, so you must be vigilant.

At first glance, the compressors appeared to be operating normally. There were no active alarms, the oil temperatures were still within acceptable limits, and the control panels showed nothing that immediately explained the moisture problem. Sarah then noticed how hard the compressor cooling fans seemed to be working. That observation led her to check something no one had measured during the original investigation: the temperature and flow of the cooling air entering the compressor room.

She walked outside to inspect the fresh-air intake louver and immediately saw a problem. A storage rack had been installed close to the wall, pallets of packaging materials had accumulated nearby, and the intake screen was heavily coated with dust and debris. The opening was not completely blocked, but the available airflow had been severely restricted. The compressors were unable to draw in enough cool outdoor air to carry away the heat they produced.

Because the hot air was not being removed effectively, some of it circulated back toward the cooling air intake. Sarah measured the air entering the compressor room and found that it was nearly 18° F (10° C) warmer than the outdoor ambient temperature. That seemingly small temperature difference had a surprisingly large impact. Rotary screw compressors reject nearly all of the electrical energy they consume as heat, so their cooling systems depend on a continuous supply of cool, unrestricted inlet air.

When cooling airflow is restricted, the compressor coolers cannot remove heat efficiently. Compressor discharge temperatures rise, the lubricant operates at a higher temperature, and the compressed air leaves the compressor carrying a greater heat and moisture load into the downstream treatment equipment.

The refrigerated dryer had not failed. It was simply being asked to cool compressed air that was much hotter than it had been designed to handle. As that hot compressed air traveled through cooler piping in the plant, additional water vapor condensed into liquid — overwhelming filters, drains, and end-use equipment.

Sarah’s maintenance crew immediately removed the stored materials, cleaned the intake screen, and restored a clear path for cooling air to enter the compressor room. They also inspected the hot-air discharge duct to ensure the hot air was being exhausted outdoors instead of recirculating back toward the compressor air intake. Within minutes, the inlet cooling air temperature began to fall. Compressor discharge temperatures dropped as well, allowing the refrigerated dryer to operate under the conditions for which it had been designed.

Over the following week, the improvement became obvious throughout the plant. Filter bowls remained dry, automatic condensate drains cycled far less frequently, pneumatic equipment operated reliably, and operators stopped reporting moisture-related production problems. Sarah documented the incident for her maintenance team because the lesson was too valuable to forget. Everyone had focused on the symptom; water in the compressed air system and assumed the dryer was at fault. In reality, the root cause had been restricted inlet cooling airflow that caused the compressors to operate at elevated temperatures.

The experience reinforced an important principle of compressed air system optimization. Compressors, coolers, dryers, filters, piping, and ventilation all work together as a system, and a problem in one area often appears somewhere else. Sometimes solving a compressed air moisture problem does not require a new dryer, larger filters, or expensive equipment upgrades. Sometimes the most effective solution is simply restoring an unrestricted supply of cool inlet air so the compressors can reject heat as they were designed to do.

 


Filed Under: Air Compressors, Air Preparation, Components, Compressed Air Technologies, Featured, Pneumatic Tips

 

About The Author

Paul Heney

Current Digital Issue

Fluid-Power-World-November-2026-issue-Cover-feature-image-template-copy

A note from the editor This issue takes a look at some of the practical challenges engineers face when designing, maintaining and troubleshooting fluid power systems. Our Design Notes feature explores the particularly harsh environment of tunnel boring machines, where moisture and contamination can quickly become reliability problems. Eaton’s filtration expert weighs in here on…

View Back Issues

Subscribe!

Fluid Power World is written by engineers for engineers engaged in designing machines and or equipment in Off-Highway, Oil & Gas, Mining, Packaging, Industrial Applications, Agriculture, Construction, Forestry, Medical and Material Handling. Fluid Power World covers pneumatics, mobile hydraulics and industrial hydraulics.

Fluid Power Design Guides

fluid
“fpw
EXPAND YOUR KNOWLEDGE AND STAY CONNECTED
Get the latest info on technologies, tools and strategies for Fluid Power Professionals.

RSS feed: Featured White Papers Featured White Papers

  • Moving fluid power forward
  • High-force linear motion: How to convert from hydraulic cylinders to electric actuators and why.
  • A technical comparison: Performance of pneumatic cylinders and electric rod actuators
Fluid Power World
  • Hose Assembly Tips
  • Mobile Hydraulic Tips
  • Pneumatic Tips
  • Sealing & Contamination Control Tips
  • About us
  • Contact Us

Copyright © 2026 Arrowfly LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Arrowfly
Privacy Policy | Advertising | About Us

Search Fluid Power World

  • Home
  • Technologies
    • Hydraulics
      • Cylinders & Actuators
      • Filtration/Contamination Control
      • Fittings, Couplings & Adapters
      • Fluids
      • Fluid Conditioning
      • Hose & Tubing
      • Pumps & Motors
      • Related Technologies
      • Sealing
      • Sensors & Gauges
      • Valves & Manifolds
    • Pneumatics
      • Air Preparation & Regulation
      • Compressed Air Technologies
      • Cylinders & Actuators
      • End Effectors & Grippers
      • Fittings, Couplings & Adapters
      • Hose & Tubing
      • Sensors
      • Vacuum
      • Valves & Manifolds
  • Engineering Basics
  • Trending
  • Resources
    • Digital Issues
    • Pneumatics Tech Toolbox
    • Podcasts
    • Special Reports
    • Subscribe to Fluid Power World Print Magazine
    • Videos
    • Webinars / Digital Events
    • White Papers
  • Women in Engineering
    • Women in Fluid Power
    • Women in Engineering
  • Design Guides
  • Classrooms
    • Hydraulic Filtration
    • Hydraulic System Design
    • Pneumatics Classroom
  • Advertisers
    • Advertise
    • PR Submissions
    • Eblast Submissions
  • SUBSCRIBE